Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in Denver?
Gate parts and welding in Denver typically run $150 to $450 for common part replacements and small welding repairs, while larger jobs like operator replacement, gate-frame fabrication, or heavy hinge repair land between $650 and $3,500 depending on the gate type, the operator brand, and how much fabrication is needed. Most residential part swaps and minor weld repairs finish in a single visit. Every job gets a free written estimate, so the number you see before work starts is the number you pay.
We’re gate-only specialists, which means the diagnosis happens fast: whether your opener stopped responding or your gate won’t move at all, we’ve seen the failure mode before and we know which parts and welds are involved. We work on the brand you already own, from LiftMaster and FAAC to DoorKing and Mighty Mule. Call (855) 677-8291 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Key Takeaways
- Small part replacements and minor welds in Denver: roughly $150 to $450.
- Operator replacement, heavier welding, or swing-arm work: roughly $650 to $3,500.
- Free written estimates, with the price set per job after we see the gate.
- We service nine major operator brands and handle both repair and installation.
- Denver’s freeze-thaw cycle is a real driver of hinge, track, and post-footing wear.
Gate Parts & Welding Cost Breakdown (2026)
Here’s a realistic picture of what the line items look like in the Denver market. These are typical estimated ranges. The written estimate after an on-site look sets the final price.
| Line item | Typical estimated range |
|---|---|
| Roller replacement (per gate) | $150 – $350 |
| Hinge replacement or re-weld | $175 – $400 |
| Latch and catch hardware | $150 – $300 |
| Gate-frame crack repair or re-weld | $250 – $600 |
| Post hinge re-weld and re-hang | $300 – $750 |
| Track or guide replacement | $300 – $700 |
| Swing-arm or slide operator replacement | $650 – $2,200 |
| Control board or receiver replacement | $250 – $550 |
| Safety sensor / photo-eye replacement | $175 – $375 |
| Keypad, remote, or access-control reprogramming | $150 – $350 |
| Custom gate fabrication (per panel) | $1,200 – $3,500 |
What pushes a job toward the top of a range? Fabrication is the big one. If a weld has to be cut out and rebuilt, or a custom bracket has to be made because the original part is discontinued, labor climbs. Premium operator brands cost more to replace than basic swing-arm units. And access matters: a wide, well-lit driveway is faster to work on than a tight side-yard gate with limited clearance.
What keeps a job at the low end? Straightforward part swaps on a gate that’s structurally sound. If your gate only needs new rollers and a latch, you’re likely looking at the lower figures. For the broader picture on repairs across the metro, see our gate repair Denver page.
What Affects Gate Parts & Welding Pricing in Denver
- Freeze-thaw wear. Denver swings above and below freezing repeatedly through winter. That cycle works metal hardware loose, and it’s a common reason hinges, latches, and post anchors fail. Repairing that kind of wear is usually a weld-and-refit job, not a simple swap.
- Gate type. A small manual walk gate is faster to work on than a long slide gate with an operator, track, and safety sensors. Labor scales with the number of moving parts.
- Operator brand. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so parts sourcing is rarely the holdup. But some brands carry higher part costs than others when a full replacement is needed.
- Fabrication needs. Custom welding, bracket fabrication, or cutting out a failed weld adds labor hours. On older gates we sometimes find the part that failed isn’t made anymore, which means fabricating a compatible one.
- Access and site conditions. A tight, sloped, or gravel driveway into a Denver property makes moving equipment and working on the gate slower. Accessible sites keep labor down.
- Repair vs. replace. Sometimes the honest call is that a part swap won’t hold and a section of the gate needs to be replaced or rebuilt. That decision moves the number significantly, and we’ll lay out both options before you commit.
How to Save on Gate Parts & Welding
The biggest savings come from catching small failures early. A hinge that’s come loose is a modest weld job. Let it go and it can pull the post anchor and turn into a much bigger repair. A free estimate is the cheapest way to find out what you’re actually dealing with, and what it will cost.
- Get it looked at early. Diagnosing a rattle or sag before it becomes a structural failure keeps the job in the low range.
- Fix the mechanism before the operator. If the gate is binding, the operator works harder and wears out faster. Repairing the track and hinges first can spare the operator.
- Ask about part availability. When we can source a standard part, it’s cheaper than fabricating one. Knowing which is needed is part of the free estimate.
- Get the written estimate. We price per job, so you see the itemized number before work starts. No surprises, and no fee for the estimate itself.
Call (855) 677-8291 for a free estimate and a straight answer on whether it’s a part swap, a weld, or something more. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Is gate parts and welding a job you can do yourself?
Some parts swaps, like a latch or a remote battery, are safe for a handy homeowner. Welding a gate frame, re-anchoring a hinge into a post, and working on an operator’s control board or wiring are not. Gate panels are heavy and can crush, and a powered operator carries live voltage and stored force. On those we recommend a trained technician. A gate that fails mid-travel can swing or slide with force, so call us and we’ll handle the diagnosis safely.
How long does gate parts and welding take in Denver?
Most part replacements and minor welds are done in a single visit, often within an hour or two on site. Heavier fabrication, post re-anchoring, or full operator replacement can take longer and may need a return visit once parts are in hand. We give you a realistic time frame in the written estimate. For most Denver homeowners, the goal is one trip and a working gate.
Can you fix my gate operator, or do I need a new one?
In many cases we repair the operator rather than replace it. Control boards, receivers, safety sensors, and remotes are common failure points that we can fix. When the operator’s motor or gearbox has failed beyond repair, replacement is the honest answer. Because we work on nine major brands, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, we’re rarely stuck for parts. We’ll tell you which path is cheaper for your gate.
FAQs – Gate Parts & Welding Cost
How much does gate welding cost in Denver?
Gate welding in Denver typically runs $250 to $750 for a frame crack, hinge re-weld, or post re-anchor, with heavier fabrication costing more. The written estimate sets the exact price after we see the gate. Call (855) 677-8291 for a free quote.
How much does it cost to replace a gate operator in Denver?
Operator replacement usually falls between $650 and $2,200, depending on the brand and gate type. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule systems. Call (855) 677-8291 and we’ll price it for the brand you own.
Is it cheaper to repair or replace my gate?
Repair is almost always cheaper when the gate’s frame and posts are sound. A part swap or weld typically runs $150 to $750, while replacing a gate usually starts well over $1,200. We’ll tell you clearly which makes sense. Estimates are free.
Can you come today?
Often, yes. Fast dispatch runs 7am to 7pm, Sunday through Friday, and same-day service is common for part and weld work. Call (855) 677-8291 to check availability. We answer 24/7. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm.
Do you charge for a gate estimate in Denver?
No. Estimates are free, and we price each job from the written estimate after looking at the gate. Call (855) 677-8291 to schedule one. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. If you want to understand repair options across the metro, our Denver service page covers more.
From manual swing gates to fully automated electric systems
We handle both repair of your existing gate and installation of a new one, so you don’t need to bring in a second contractor. Whether the problem is a hard mechanical failure, a weld that’s let go, or an automated system that’s stopped responding, the trade is the same and we stay inside it. Gate Repair Denver has been serving this market since 2015, and we’re gate-only specialists, not a generalist who also happens to fix gates.
Call (855) 677-8291 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Tell us the brand and the symptom, and we’ll set up a time to diagnose and fix it.
Pricing reflects the Denver market as of 2026. Gate Repair Denver offers free estimates – call (855) 677-8291.
What Our Customers Say
"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."
- Emily Brooks"Repair is holding. He was quite a bit later than the window I was given, and the office didn't call me about it, I had to call them. The work itself was done well once he got here."
- Tara Padgett"Fixed the immediate problem. He was honest that the operator is near end of life and I should budget for a replacement, which I appreciate even if it wasn't what I wanted to hear."
- Daniel Gallagher