Gate Installation in Denver - Written Price, Install Date Set

Trusted Gate Installation for Denver Homeowners

A gate that hangs wrong, binds halfway, or runs on an operator that never quite fits the driveway is the problem we solve. Gate Repair Denver is a gate-only shop: we install new swing and slide gates, we handle the electric and automated side, and we repair what’s already there. We’ve been serving Denver since 2015, and because gates are all we do, we diagnose fit and hardware issues faster than a crew that splits its time across four trades. If your gate hasn’t been installed yet or the old one is past saving, call (855) 677-8291. We answer 24/7, and we can often get a free estimate scheduled the same day.

Call (855) 677-8291

Automatic Gate Installation

Automatic Gate Installation means fitting a gate and its powered operator together as one system, so the leaf, the hinges, the stops, and the drive all agree with each other from day one. You need it when you want a driveway or entry gate to open without leaving the car, or when an existing manual gate has become a daily chore. We install automatic systems on both swing and slide gates, and we’re experienced with LiftMaster and FAAC operators, among others. Typical automatic gate installation in Denver runs from about $3,200 to $7,500 depending on gate size, material, and operator type, with the written estimate setting the final price. We measure first, then quote, and the price is agreed before any work starts.

Swing and Slide Automation

Swing gates use an arm or underground operator; slide gates use a rack-and-pinion drive along the track. Which one fits your property depends on slope, clearance, and how much room the gate has to travel. We walk the site and recommend the drive that matches the layout rather than the one that’s easiest to sell.

Safety and Accessories

A powered gate needs safety edges, photo eyes, and a proper control enclosure so it stops when something is in the path. We install those as part of the job, not as an afterthought. Access control, keypads, and remotes get wired and tested before we hand over the gate.

Gate Installation Services

Gate Installation Services cover the whole job: choosing the gate, setting the posts, hanging the leaf, fitting the operator, and commissioning the system so it works the way it should. You need this when you’re adding a gate for the first time, replacing a gate that’s rusted or sagging past repair, or reworking an entry that never functioned correctly. We handle both the mechanical gate and the electric side under one roof, so you don’t need a second contractor for the automation. Most residential gate installations in Denver land between $1,800 and $6,500, depending on material, span, and whether the gate is automated. We measure on site and put the number in writing before we order anything.

Manual Gates Done Right

A manual gate still needs correct posts, solid hinges, and a latch that lines up every time. We set posts to proper footing depth and check the swing before we ever hang the leaf. It’s the part most installations get wrong and the reason gates start dragging within a year.

Replacing an Old Gate

Sometimes the frame is fine and only the leaf needs replacing; sometimes the whole assembly has to come out. We check the posts and hardware before recommending either path. That keeps you from paying for a new gate when a repair would do the job.

Electric Gate Installation

Electric Gate Installation is the powered side of a gate project: the operator, the wiring, the control board, and the safety devices that make an automated gate legal and safe to use. You need it when a gate has to open for vehicles without someone getting out, or when an existing electric gate has failed and the old system is beyond economical repair. We install electric systems on LiftMaster and BFT hardware and wire the power run and safety edges as part of the job. Electric gate installation in Denver typically runs $2,800 to $6,800, with the written estimate setting the final figure. The price is quoted and agreed before we start.

The Power Run

An electric gate is only as reliable as the power feeding it. We plan the run from the panel to the operator, size the conduit correctly, and keep the low-voltage control wiring separate from the line voltage. If the run is complicated, we say so up front instead of discovering it mid-install.

Control Boards and Remotes

The control board is where most gate problems eventually show up, so we install it in a protected enclosure and program the remotes and keypad at handover. We test every input and every safety device before we consider the job finished. You leave knowing how the gate behaves, not guessing.

Driveway Gate Installation

Driveway Gate Installation puts a gate across the vehicle entrance, sized and hung so it clears the driveway surface and doesn’t drag through snow or gravel. You need it when you want to control access to the property, close off a driveway from the street, or replace a gate that’s too narrow or too light for the wind and traffic it faces. We build and install driveway gates in wood, steel, and ornamental metal, and we can automate them in the same visit. Driveway gate installation in Denver runs roughly $2,200 to $7,000 depending on width, material, and whether it’s powered. We measure the opening, check the grade, and quote in writing before work begins.

Width and Clearance

Driveway gates have to clear the vehicle, the mirror, and the ground, and that last one is where most installs go wrong. We check the driveway slope and the gate’s underside clearance before we choose a leaf size. A gate that scrapes the concrete in winter is a gate that will fail early.

Matching the Property

A driveway gate is the first thing anyone sees, so material and finish matter as much as function. We’ll walk through the options in steel, wood, or metal and match the gate to the house rather than to a catalog page. You get a gate that looks intentional, not bolted on.

Sliding Gate Installation

Sliding Gate Installation puts the gate on a track or cantilever so it rolls sideways instead of swinging out, which is the right call when the driveway is short or the gate would otherwise swing into traffic. You need it when a swing gate won’t fit the space, when the grade makes a swing gate awkward, or when you want a wider opening than a swing leaf can reliably cover. We set the track, level it, and fit the rollers and guide so the gate travels true. Sliding gate installation in Denver typically costs $3,000 to $7,800 depending on span, gate weight, and whether it’s automated. We measure the run and quote in writing before any work starts.

Track vs. Cantilever

A track gate needs a level concrete pad running the full length of travel. A cantilever gate hangs from a carriage and needs no ground track, which suits driveways that slope or where snow and debris would foul a track. We check the site and recommend the one that will actually work.

Keeping It on the Rails

Heavy slide gates can come off the track if the rollers wear or the guide posts shift, which is a genuine crush hazard. We set the posts to proper footing depth and align the guide so the gate can’t ride up. Safety is the reason to have a specialist install this, not a generalist.

Gate Opener Installation

Gate Opener Installation fits the motor and control system that turns a manual gate into an automated one, and it’s the job that most often goes wrong when it’s done without matching the operator to the gate. You need it when your gate is manual and you want it powered, or when an old opener has failed and the gate itself is still sound. We install LiftMaster, FAAC, and Linear operators, and we size the opener to the actual gate weight and swing arc. Gate opener installation in Denver typically runs $1,400 to $3,600 including the operator and safety devices. We measure, quote in writing, and agree the price before any work starts.

Matching Opener to Gate

An undersized operator burns out; an oversized one beats the gate apart. We weigh the leaf, check the hinge condition, and pick an opener rated for the load. That’s the difference between a gate that lasts and one that’s back on the repair list in eighteen months.

Programming and Handover

Once the opener is fitted, we program the remotes and keypad and test the safety reverse and photo eyes. You get a walkthrough of how the gate opens, closes, and stops. If something doesn’t feel right, we fix it before we leave.

Gate Fabrication

Gate Fabrication means building a gate to fit an opening that standard sizes won’t cover, or matching a style, material, or security requirement that off-the-shelf gates can’t meet. You need it when your driveway is an odd width, when the property has an architectural style to match, or when you want a gate built for the wind and traffic it will actually see. We fabricate in steel, wood, and ornamental metal and fit the hardware as part of the build. Custom fabrication in Denver usually runs $2,500 to $8,500 depending on material, size, and finish. We measure the opening, agree a design, and quote in writing before any metal is cut.

Design and Material

A fabricated gate has to balance weight, strength, and the way it looks from the street. We talk through material and finish before we build, because changing a design after fabrication is expensive. The goal is a gate that fits the opening and the house at the same time.

Built for the Site

Denver’s freeze-thaw swings are hard on gate hardware, so we build with drainage and movement in mind. Posts go to proper footing depth and the frame is detailed so water doesn’t sit in the joints. That’s how a fabricated gate stays true through the seasons.

Brands We Service

We service LiftMaster equipment and know where it wears out: the limit switches, the control board, and the safety inputs are the usual suspects on a gate that’s stopped responding. FAAC operators are common on swing gates, and we’re familiar with their arm geometry and the way their control logic behaves when a safety edge faults. BFT systems show up on heavier slide gates, and we know their drives and how they handle load. Linear operators are another make we see often, and we know their remote programming and their failure points.

Because we’re a gate-only shop, we work on the brand you already own rather than pushing you toward a replacement. We don’t stock parts for every system, but we can source what a job needs and we’ll tell you honestly when a repair is the better call than a new install. Whether you have LiftMaster, FAAC, BFT, Linear, or any other make, we can help.

Signs You Need a Pro Right Now

• The gate drags or binds. A gate that scrapes the ground or sticks halfway usually means a hinge, post, or track problem. Left alone, it puts strain on the operator and shortens its life.
• The opener runs but the gate doesn’t move. That points to a stripped gear, a failed clutch, or a broken arm. It’s a mechanical fault, not an electrical one, and it needs a technician who knows the difference.
• The gate won’t close all the way. A safety edge or photo eye that’s misaligned will stop the gate mid-travel. That’s a safety device doing its job, and it needs proper diagnosis rather than a bypass.
• Loose posts or a leaning gate. A post that’s shifted means the footing has failed, and a gate hanging off a bad post can fall. Stop using it and have it checked.
• The remote stopped working and reprogramming won’t hold. A control board or receiver on the way out will drop programming repeatedly. That’s a repair, not a user error.

Our Process, Step by Step

1. 1
   Call and describe the gate. Tell us the type, the width, and whether it’s manual or powered. We use that to know what to bring and whether it’s a repair or an install. We answer 24/7.
2. 2
   On-site measure and inspection. We check the opening, the grade, the posts, and the power situation. For automated gates we look at where the power run will go and how the safety devices will mount.
3. 3
   Written estimate. You get a clear written price that covers the gate, the hardware, and the labor. The price is quoted and agreed before any work starts, so the invoice matches the estimate.
4. 4
   Fabrication and scheduling. If the gate needs building or ordering, we handle that and schedule the install around it. You’ll know the timeline before we commit.
5. 5
   Install, test, and handover. We set the posts, hang the gate, fit the operator, and test every safety device. We program the remotes and walk you through how the gate works before we leave.

How Much Does Gate Installation Cost in Denver?

Our Service Area Near Denver

We install and repair gates across Denver and the surrounding communities, including Four Square Mile, Dakota Ridge, Castle Pines, Welby, Sherrelwood, Berkley, Commerce City, Englewood, and Federal Heights. Response times depend on the day and the location, but we schedule installs and estimates from 7am to 7pm, Sunday through Friday.

If you’re in one of the outlying neighborhoods, call and we’ll give you a straight answer on scheduling. You can also read more about our Denver service and our Four Square Mile coverage.

Frequently Asked Questions About Gate Installation in Denver

Schedule Your Gate Installation Service in Denver Today

Whether you’re adding a new automatic gate, replacing a failing one, or fitting an opener to a gate that’s already there, we can help. Call (855) 677-8291 for a free, no-obligation estimate. We answer 24/7, we dispatch from 7am to 7pm, Sunday through Friday, and the price is quoted and agreed before any work starts. Gate installation in Denver, done by gate-only specialists.

Written by Vernon Hobbs, Owner at Gate Repair Denver, serving Denver since 2015.