Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Installation Cost in Denver?
Gate installation in Denver typically runs $1,800 to $6,500 for a manual swing gate and $3,500 to $12,000 or more for a fully automated electric gate, including the operator, sensors, and safety equipment. A single small walkway gate at the low end of the market generally lands between $900 and $2,200. The final number depends on the gate material, the width of the opening, whether the ground is level, and how much electrical work the operator needs.
In the Denver market, a standard driveway swing gate is usually between $3,200 and $7,600 once you add the automation package and safety devices. Sliding gates tend to sit higher because they need a track, proper footing, and a heavier duty operator. Historic and hillside lots in the area often push a project toward the upper end of these ranges. Every job is priced per job by a written estimate after we look at the site, so the numbers here are typical ranges rather than a quote for your specific gate.
We handle gate installation, gate repair, and electric gate repair as our only work, so we’re not a general contractor or a fence company adding gates on the side. If you want a real figure, call (855) 677-8291. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Key Takeaways
- Manual swing gate installation in Denver usually runs $1,800 to $6,500.
- Automated electric gate installation starts around $3,500 and climbs past $12,000 for wide openings and heavy materials.
- Automation adds $1,200 to $4,500 on top of a manual gate, depending on the operator and safety setup.
- Denver ground and slope conditions are a bigger cost driver here than most homeowners expect.
- Estimates are free, and the written estimate sets the final price.
Gate Installation Cost Breakdown (2026)
This table breaks down what a typical Denver gate project includes. Each line is an estimated range, and not every project needs every line. A small walkway gate might only add a few of them. A full driveway automation package uses almost all of them.
| Line item | Typical range (Denver, 2026) |
|---|---|
| Single walkway or garden gate, installed | $900 – $2,200 |
| Manual driveway swing gate, installed | $2,400 – $5,800 |
| Sliding gate with track and footing | $3,800 – $9,500 |
| Swing gate operator, installed | $1,200 – $4,000 |
| Slide gate operator, installed | $1,500 – $4,500 |
| Safety loop, photo eye, and edge sensors (entire package) | $350 – $1,100 |
| Keypad, phone app module, or remote package | $300 – $900 |
| Low-voltage wiring run to a nearby power source | $400 – $1,600 |
| New concrete footing or pad | $600 – $2,500 |
| Removal of an old gate | $150 – $500 |
The single biggest cost jump happens when a gate crosses from manual to automated. Once you add an operator, the safety devices that go with it, and a reliable low-voltage run, you’re typically adding $1,200 to $4,500 on top of the gate itself. Material drives the rest. A basic steel tube gate costs far less than a custom-welded or wrought-style gate, and something heavy enough to feel solid on a snowy Denver driveway also needs a heavier operator to move it reliably.
One thing worth knowing: some quotes look cheap because they leave out the safety package. On an automated gate, the photo eyes and safety edges aren’t optional extras. They’re what stops the gate from closing on a car, a pet, or a person. We put them in every estimate that involves an operator so you can see the real number. If you’ve ever wanted a clear explanation of what an install actually includes, that’s what a gate repair denver team looks at every day.
What Affects Gate Installation Pricing in Denver
Two homes on the same block can see wildly different quotes, and in Denver it’s rarely the gate itself that causes it. Usually it’s the ground, the power, or the layout. Here’s what moves the number most.
- The ground under the posts. Denver’s shifting clay soils and freeze-and-thaw cycles are hard on footings, and grading varies from block to block. If the grade is uneven or a gate needs a deeper concrete pad, the footing line climbs toward the top of its range. Posts have to sit on a proper footing depth, not just a shallow hole.
- Slope and yard layout. Lots across the Denver area often slope toward the street or along a side yard. A sloped driveway means extra hardware for a swing gate to clear the ground as it opens. A flat lot is simpler and cheaper to install.
- Gate width and material. A 4-foot walkway gate and a 16-foot double driveway gate aren’t the same job. The wider and heavier the gate, the more operator power, footing, and safety hardware you need.
- Power and wiring. The operator needs electricity, and sometimes the nearest outlet or panel is a long way from the gate. A short low-voltage run is cheap. A long trench and a new circuit push the wiring line toward its top range.
- The operator you choose. We install and service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule systems. Each has a different price point and different strengths. A residential swing gate and a commercial-grade slide operator built for high traffic sit at opposite ends of the range.
- Access control and features. A simple remote is one thing. Keypads, intercoms, phone app control, and multi-remote setups add cost but make the gate far more usable day to day.
The right operator for your gate is the one that matches its weight, its opening type, and how often it runs. That’s the part we take seriously as gate-only specialists. We work on the brand you already own, and if you’re starting fresh we’ll match one of those nine systems to your setup rather than sell you the most expensive option.
Can You Save Money on Gate Installation in Denver?
Yes, and most of the savings come from planning before anyone digs. A few choices move the price down without cutting corners:
- Match the gate to the job. A reasonable steel swing gate with a solid operator costs far less than a custom ornamental gate and performs well for years. If curb appeal matters more than ornamentation, a clean standard design saves money.
- Stay close to power. If you have a choice about where the gate goes, a location near an existing outlet or panel can cut the wiring line substantially.
- Do the site prep early. Clearing brush, marking the opening, and deciding on the layout before we arrive keeps the install on schedule. We do the digging and concrete; you just tell us where the line should be.
- Bundle the whole job. Installing a new gate and its operator together is cheaper than adding automation to a gate months later, when the wiring and footing get handled in a second visit.
- Get a written estimate before work starts. A written estimate sets the final price, so you know what you’re paying before a post goes in the ground. Estimates are free. Call (855) 677-8291.
We serve homeowners, landlords, and property managers across Denver. If your gate project is on an older property that’s had a gate before, we’ll also check whether the existing footing or wiring can be reused, which can save real money.
Is It Cheaper to Repair an Existing Gate or Install a New One?
Repair is usually cheaper when the gate frame is sound: fixing an operator, replacing a hinge, or correcting a sensor often costs a fraction of a new install. Replacing makes more sense when the frame is bent, rusted through, or undersized for the operator you want. As a rule of thumb, if a repair lands above about $1,500 on a gate that’s already tired, a new install is worth pricing side by side.
We repair and install, so we don’t have a reason to steer you one way or the other. We’ll tell you honestly what a repair gets you and what a new gate would cost, and you decide. For a straight answer on your gate, call (855) 677-8291. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Do You Install Every Kind of Gate?
We install manual swing gates, sliding gates, walkway gates, and fully automated electric systems. Our work covers the operator, the access control, the sensors, and the wiring, all in one job. Because we specialize in gates and gate operators rather than fences or garage doors, we spend our time on the parts that actually make a gate work. From manual swing gates to fully automated electric systems, we handle the whole install.
The one part we don’t do is run a new high-voltage circuit from your main panel. That’s electrician work, and Denver’s rules about who can do it apply. A trained professional should handle anything at the panel. We’ll tell you plainly if your job needs that step so you’re not caught by surprise. If a gate ever stops responding or won’t move at all, we diagnose and fix it, whether your opener stopped responding or your gate won’t move at all.
How Long Does a Gate Installation Take?
A simple manual walkway gate is often a one-visit job. A full driveway install with automation and wiring usually takes one to three visits depending on the footing, the power run, and the operator. New concrete needs time to set before the gate hangs on it, and that’s the part that sets the schedule as much as anything. We’ll give you a realistic timeline with your estimate so you know what to expect.
If your gate failed suddenly and you can’t wait, call us and we’ll look at repair first. A gate that’s been hit, stuck, or knocked off its track often gets moving again faster than a new install. If a door fails, call and we’ll book you in. Call (855) 677-8291. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
FAQs – Gate Installation Cost
How much does a basic gate installation cost in Denver?
A basic manual swing gate installation in Denver typically runs $1,800 to $6,500 depending on width, material, and footing. A small walkway gate can land closer to $900 to $2,200. Call (855) 677-8291 for an exact quote: estimates are free.
How much does an electric gate cost in Denver?
A fully automated electric gate in Denver usually runs $3,500 to $12,000 or more including the operator, sensors, and wiring. The operator alone adds $1,200 to $4,500 on top of a manual gate. Call (855) 677-8291 and we’ll price your specific gate.
Is it cheaper to repair or replace my gate?
Repair usually costs less than replacement when the frame is solid. A common operator repair runs well under $1,000, while a new automated install sits in the thousands. If a repair climbs past roughly $1,500 on a worn gate, price a new one alongside it. Call (855) 677-8291 and we’ll give you both numbers.
Do I need permits to install a gate in Denver?
Many gate installations, especially those with electrical work or attached to a property line, can require a permit, so ask the City and County of Denver building department before work starts. Rules vary by lot and by what the gate touches. We’ll flag anything you should check before we begin. Call (855) 677-8291 with questions.
Can you install a gate and an operator at the same time?
Yes, and it’s usually the cheaper way to do it. Installing the gate and its LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, or Mighty Mule operator in one project saves a second visit for wiring and setup. Call (855) 677-8291 for a combined estimate.
How much does a sliding gate cost to install in Denver?
A sliding gate with track and footing typically runs $3,800 to $9,500 installed in Denver, before any operator. Slide operators add $1,500 to $4,500 depending on the weight the gate carries. Call (855) 677-8291 for a written estimate.
Contact Us for a Free Gate Installation Estimate
If you’re planning a gate and want a real number instead of a guess, we’ll come out, look at the site, and put the price in writing. Our estimates are free, and the written estimate sets the final price. Gate Repair Denver has served the area since 2015, and gates are all we do: repair, electric gate repair, and installation. Your gate, diagnosed and fixed, not guessed at. Call (855) 677-8291 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Gate Repair Denver, serving Denver since 2015.
Pricing reflects the Denver market as of 2026. Gate Repair Denver offers free estimates – call (855) 677-8291.
What Our Customers Say
"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."
- Emily Brooks"Repair is holding. He was quite a bit later than the window I was given, and the office didn't call me about it, I had to call them. The work itself was done well once he got here."
- Tara Padgett"Fixed the immediate problem. He was honest that the operator is near end of life and I should budget for a replacement, which I appreciate even if it wasn't what I wanted to hear."
- Daniel Gallagher