Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Repair for Denver Homeowners
A gate that won’t open is a problem you feel immediately. Something in the mechanism has failed, whether it’s a hinge that’s pulled loose, a track that’s out of line, or an operator that’s stopped responding to the remote. We’re gate-only specialists, which means when we come out to look at yours, we’re not splitting our attention between fencing, landscaping, or garage doors. We work on manual swing gates and fully automated electric systems, and we handle both the mechanical side and the electronics under one roof.
Gate Repair Denver has been serving the metro since 2015. Vernon Hobbs leads our crew, and we answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. Call (855) 677-8291 for a free estimate.
Driveway Gate Repair
Driveway Gate Repair covers the gate your vehicles actually pass through, which means it takes more wear than any other gate on the property. When the opening gets sluggish, the gate drags on the ground, or the operator strains and stops partway, that’s the time to have it looked at before the motor burns out. We diagnose the cause rather than guessing at parts, and because we specialize in gates we can usually pinpoint the failure on the first visit. A typical driveway gate repair in Denver runs $180 to $450 depending on what’s failed and whether the fix is mechanical or electrical. The written estimate sets the final price, and we quote it before any work starts.
Hinge and Post Failures
Driveway gates are heavy, and the hinges and posts carry that load every single day. When a hinge starts to sag or a post shifts, the gate drops out of square and the operator has to fight it. Fixing the hinge or resetting the post early protects the rest of the system.
Operator and Sensor Troubleshooting
When an automatic driveway gate stops responding, the cause is usually in the operator, the sensors, or the wiring that connects them. We test the control board, the safety edges, and the travel limits to find where the signal is breaking down. That means fewer return visits and a fix that holds.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Gate Welding
Gate Welding is the structural repair that keeps a metal gate from failing completely, and it’s needed when a weld has cracked, a hinge has torn away from the frame, or impact has bent a panel at the joint. We weld steel and iron frames and reattach hardware properly, so the repair is as strong as the original construction. This isn’t a cosmetic touch-up; it’s rebuilding the joint so the gate carries its weight again. Gate welding in Denver typically runs $150 to $400 depending on how much has to be cut out, ground, and re-welded. We give you a written estimate before we strike an arc, and the estimate is free.
Structural Cracks and Stress Points
Cracks usually start at the corners of the frame or where the hinge meets the stile, because that’s where the stress concentrates. A crack that’s ignored will spread and eventually split the joint. We cut back to sound metal before welding, so the repair lasts.
Rebuilding Torn Hardware Mounts
When a hinge or latch tears out, the mounting surface is usually distorted and needs to be rebuilt, not just re-drilled. We clean the joint, square it up, and weld new material where it’s needed. That gets the hardware back in its correct position.
Commercial Gate Repair
Commercial Gate Repair is the work that keeps access control running for a business, apartment building, or managed property, where a gate that’s down becomes a security and liability problem fast. Parking gates, restricted-access entrances, and heavy-duty automated systems all fall into this category. We handle the operator, the access control hardware, and the mechanical structure, so a commercial property manager doesn’t have to coordinate several contractors. Commercial gate repair in Denver usually runs $250 to $650 depending on the system and how much of it has failed. The estimate is free and written, and we agree on the price with you before we start.
Access Control and Entry Systems
Commercial gates tie into keypads, card readers, and intercoms, and when one part of that chain fails the whole entry stops working. We test the access hardware against the operator to find which piece is at fault. That saves time for your tenants and your staff.
High-Cycle Operator Service
Gates that open dozens of times a day wear faster than a residential gate ever will. The drive components, the limits, and the safety devices all need attention sooner. We set the system up so it handles the cycle count it actually sees.
Iron Gate Repair
Iron Gate Repair handles the heavy ornamental and security gates that anchor an entrance, and it’s needed when the gate has rusted, sagged, or lost its swing because the hinges have worn. Iron gates are built to last, but that also means they’re heavy, and the hardware has to be strong enough to carry them. We repair the frame, the hinges, and the latch so the gate swings clean again, and we treat rusted areas so the corrosion doesn’t spread. Iron gate repair in Denver typically runs $200 to $500 depending on the condition of the metal and the hardware. We quote per job with a free written estimate before any work begins.
Rust and Corrosion Treatment
Denver’s dry air slows rust down, but it doesn’t stop it, and a gate that holds moisture in its joints will corrode from the inside. We remove the loose material and seal the bare metal so the rust doesn’t come back through the finish. That buys years on the gate’s life.
Heavy Gate Hinge Replacement
An iron gate puts serious load on its hinges, and when they wear the gate drops and drags. We replace worn hinges and rebalance the gate so it swings without resistance. That takes the strain off the operator too.
Sliding Gate Repair
Sliding Gate Repair addresses the gates that track along the ground or hang from an overhead rail, and it’s needed when the gate starts to bind, jump the track, or stall halfway. Sliding gates are unforgiving about alignment, because a track that’s off by a little makes the whole gate drag. We check the track, the rollers, the guide posts, and the operator, then correct whatever is out of line. Sliding gate repair in Denver generally runs $180 to $450 depending on whether the problem is in the track, the rollers, or the drive. The estimate is free and written, and the price is agreed before work starts.
Track and Roller Alignment
A sliding gate that binds is usually telling you the track has shifted or a roller has worn flat. Left alone, that drag overloads the operator. We re-level the track and replace the rollers so the gate glides instead of fighting.
Slide Gate Safety Devices
A sliding gate is a moving barrier with real weight behind it, and its safety edges and obstruction sensors need to be working every time. We test the reversing function and the safety edges as part of the repair. If a safety device is failing, we treat that as a priority.
Wrought Iron Gate Repair
Wrought Iron Gate Repair focuses on the decorative ironwork that gives an entrance its character, and it’s needed when the scrollwork has cracked, the pickets have bent, or the finish has broken down. Wrought iron is as much a visual feature as it is a barrier, so the repair has to restore both the structure and the appearance. We straighten bent sections, weld cracked joints, and prep the surface for refinishing. Wrought iron gate repair in Denver typically runs $200 to $500 depending on how much of the ironwork needs rebuilding. The written estimate is free, and we quote it before we touch the gate.
Straightening Bent Pickets and Panels
Impact damage bends the pickets and twists the panel, and bending them back without cracking the joints takes care. We work the metal back into line and check the frame is still square. A gate that’s out of square will not latch or swing right.
Restoring the Finish
Once the structure is sound, the finish is what keeps the gate from corrosion. We clean the bare spots and prepare the surface so the new coating bonds properly. That protects the repair and keeps the ironwork looking right.
Metal Gate Repair
Metal Gate Repair covers steel and aluminum gates of all kinds, from simple tubular frames to heavy security barriers, and it’s needed when the frame has bent, the hardware has failed, or the gate has stopped latching. Metal gates are strong but not indestructible, and a bent frame puts stress on every hinge and latch on the gate. We straighten the frame, reattach or replace the hardware, and check that the gate sits level in its opening. Metal gate repair in Denver generally runs $150 to $450 depending on the material and the extent of the damage. A free written estimate sets the price before any work starts.
Frame Straightening and Realignment
A metal gate that’s been hit or has sagged needs the frame brought back true, not just bent by eye. We measure the opening and realign the frame so the gate closes the way it was built to. That stops the latch and hinges from taking the strain.
Latch and Hardware Repair
Latches and hardware wear out or get forced, and a gate that won’t stay closed is a security gap. We replace worn hardware with parts sized to the gate’s weight. That restores a reliable close every time.
Wood Gate Repair
Wood Gate Repair keeps timber gates working when the wood has swollen, split, or loosened at the joints, which happens more than people expect in a climate with sharp swings between wet spring snow and dry summer air. When a wood gate sags, it’s usually the hinge or the brace that’s given way, not the boards themselves. We repair the joints, re-hang the gate, and replace the components that have failed so it swings and latches properly again. Wood gate repair in Denver typically runs $150 to $400 depending on the extent of the repair. We give you a free written estimate and agree the price before any work begins.
Swollen Joints and Seasonal Movement
Wood takes on moisture and swells, then dries and shrinks, and that cycle works the joints and fasteners loose. A gate that sticks in spring and rattles in summer is showing that movement. We adjust the fit and reinforce the joints that are loosening.
Sagging Gate Re-Hanging
A sagging wood gate usually needs its hinge and brace work corrected before anything else. We reset the gate in the opening and shore up the bracing so it holds its square. That keeps the gate from dragging and jamming.
See the difference
Before
After
Before
After
Before
AfterBrands We Service
We work on the brand you already own. That matters because gate operators are not interchangeable, and a technician who knows LiftMaster equipment knows where it wears out and how its limits and safety devices behave. The same goes for FAAC systems, where the control logic and setup sequence are specific enough that familiarity saves diagnostic time. We also service BFT operators and Linear systems, along with Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Our technicians are experienced with the setup and failure patterns of each of these lines.
None of that means you have to match a brand to get help. Because we’re a dedicated gate specialty and independent of any manufacturer, we diagnose the gate in front of us rather than steering you toward a system we happen to sell. Whether you have LiftMaster, FAAC, or any other make, we can help, and we can tell you plainly whether the operator needs a repair or a replacement. For automated systems that have lost programming or stopped responding, see our Electric Gate Repair page.
Signs You Need a Pro Right Now
- The gate won’t move at all. A gate that’s completely dead points to the operator, the power, or a safety device that’s tripped and won’t reset. Don’t force it open; call and let us check it, because forcing a stuck gate can bend the frame or damage the drive.
- The gate moves but won’t latch or close fully. This is usually an alignment or hinge problem, and it’s a security concern when the gate is part of your access line. It’s a repair that gets worse the longer the gate keeps trying to close against the obstruction.
- You hear grinding, scraping, or a straining motor. Noise means the mechanism is working against resistance somewhere. A gate that’s straining will eventually burn out the operator, which turns a smaller repair into a bigger one.
- The operator stops partway or reverses for no reason. That’s the sign of a limit or safety-sensor fault rather than a mechanical one. It needs testing with the right diagnostic equipment, not a guess.
- Cracks in the welds or a sagging frame. Any visible crack at a joint or hinge mount is a structural warning. A gate can drop suddenly once a failing joint lets go, so it’s worth having it looked at before it does.
Our Process, Step by Step
- 1
You call and describe the symptom. Tell us what the gate is doing (or not doing), the brand if you know it, and whether it’s manual or automated. We answer 24/7 and book you into the next opening, Sunday through Friday, 7am to 7pm. That first conversation often narrows the problem before we arrive.
- 2
We inspect the whole gate, not just the obvious fault. On site we check the frame, the hinges or track, the hardware, and the operator as one system. A gate that won’t close might have a hinge problem, a sensor problem, or both, and it’s worth finding out which.
- 3
We test the electrical side with proper diagnostic tools. For automated gates we check the control board, the travel limits, the safety edges, and the wiring. Multi-meters and operator diagnostic readouts tell us what the system thinks is happening, which is faster than trial and error.
- 4
We explain what’s wrong and give you a written price. You’ll know what failed, what it takes to fix it, and what it costs before we begin. The price is agreed, not estimated afterward. If a repair isn’t worth it, we’ll tell you that too.
- 5
We fix it and retest the full cycle. Once the repair is done we run the gate through open and close several times and check the safety devices. That final test is how we know the gate will work when we’re gone.
How Much Does Gate Repair Cost in Denver?
Gate repair in Denver usually falls between $150 and $650, and most of that spread comes down to whether the fault is mechanical or electrical and how much of the system has failed. A typical hinge or latch repair runs $150 to $250 depending on the gate’s weight and type. Welding work where a joint has cracked or hardware has torn out generally runs $150 to $400. A single operator fault on an automated gate usually lands between $250 and $450, and a commercial system with access control can reach $650. A new gate installation, by contrast, is quoted per job after we measure the opening and confirm the operator, so we don’t quote that over the phone.
What moves the price is the gate’s size and weight, the condition of the frame, whether parts need replacing or only repair, and whether the fault is one thing or several things that failed together. The way to avoid overpaying is to get a written estimate before anyone starts, and to have a specialist diagnose the actual cause rather than swapping parts until something works. Our free estimate includes the inspection, a clear explanation of what failed, and a written price, and we don’t start work until you’ve agreed to it.
Our Service Area Near Denver
We work across Denver and the surrounding metro, including Four Square Mile, Dakota Ridge, Castle Pines, Welby, Sherrelwood, Berkley, Commerce City, Englewood, and Federal Heights. Dispatch runs Sunday through Friday, 7am to 7pm, and the drive time from one part of the metro to another varies with the day, so we’ll give you a realistic window when you call. If you’re closer to the southwest side, our gate repair team covers Dakota Ridge, and our gate repair page serves Four Square Mile. For the wider metro picture, start at Gate Repair Denver.
Serving Denver, CO – Our Local Coverage Area
We serve Denver and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Gate Repair in Denver
Gate repair is the diagnosis and correction of whatever is stopping a gate from working as it should, covering both the mechanical parts and the powered system. That includes hinges, tracks, rollers, latches, frames, welding, and the operator itself. It also covers the access control and safety devices on automated gates. We handle both sides under one roof, so you don’t need a second contractor for the electrical side.
Most repairs are completed in a single visit, usually within one to three hours on site. Simple hinge or latch fixes can take under an hour, while a torn weld or an operator fault takes longer. If parts need to be ordered, we’ll tell you the timeline as part of the written estimate. We also work on gate installation when a repair no longer makes sense.
Most gate repairs in Denver land between $150 and $650 depending on the fault and whether it’s mechanical or electrical. A hinge repair is toward the low end; a commercial operator with access control is toward the high end. You get a written price before work starts, and the estimate itself is free. Call (855) 677-8291 and we’ll set up the estimate.
Yes, we service LiftMaster equipment, along with FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule systems. We’re independent and experienced with each of these lines, so we diagnose the system you have rather than steering you toward a replacement brand. Call (855) 677-8291 for an exact quote, and estimates are free.
We offer same-day service in Denver when the schedule allows. Our phones are answered 24/7, and we dispatch technicians from 7am to 7pm, Sunday through Friday. We’re closed Saturday, so a gate that fails on a Saturday is booked into the next opening. Call (855) 677-8291 and we’ll get you onto the schedule.
We stand behind the work we do and confirm the repair with a full open-and-close test before we leave. Warranty terms are set out in your written estimate, so you’ll know exactly what’s covered before any work starts. If a repaired gate isn’t behaving after we leave, call us. Call (855) 677-8291 for details.
Clear the area on both sides of the gate so our technician can inspect the full swing or travel path. Unlock any manual release or access panel, and have the gate in the position it normally sits in rather than forcing it open. If you have the operator manual or know the model, have it handy. That speeds up diagnosis. Call (855) 677-8291 to schedule.
Schedule Your Gate Repair Service in Denver Today
Whether your opener has stopped responding or the gate won’t move at all, we can diagnose it and give you a written price before any work starts. Call (855) 677-8291 for a free, no-obligation estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. Gate Repair Denver has served the metro since 2015.
Written by Vernon Hobbs, Owner at Gate Repair Denver, serving Denver since 2015.